Steel Pier Installation in Wichita, Kansas
Serving Wichita and Sedgwick County. No-pressure inspection.
📞 Call (316) 330-2902 Request an Inspection
Serving Wichita and Sedgwick County. No-pressure inspection.
📞 Call (316) 330-2902 Request an Inspection
Quick answers
Steel pier installation drives push piers or helical piers through the moving clay to load-bearing soil, then transfers the home's weight onto them. In Wichita, piers typically run $1,500 to $2,500 each installed in 2026, and a 6 to 12 pier system runs $9,000 to $25,000. The project covers pier layout, an excavation at each pier point, driving, bracketing, optional lift, and backfill.
Steel piers are the workhorse of serious foundation repair in Wichita. When a slab or basement wall has settled because the clay layer underneath is moving, the answer is to drive steel down through that clay until each pier hits something that does not move. Then the building's weight transfers off the moving soil and onto the piers. Settlement stops. In many cases, controlled lift then recovers part of the lost elevation.
A push pier is a 3 to 4 inch diameter steel pipe driven straight down in sections under the footing of the house. A hydraulic ram clamps to a bracket bolted to the footing and pushes one section down at a time. As each section goes in, the next section is added. The pier keeps going until it hits refusal, meaning the soil at that depth will not let the pipe go any further at the design pressure.
In Wichita, push pier refusal depths typically land between 15 and 30 feet, sometimes deeper on the south and east sides where the clay layer is thickest. The crew documents driven depth and final pressure on every pier. Once every pier is loaded, the system carries the structure, not the surface clay.
Push piers work best when there is enough building weight to act as resistance. That makes them a strong fit for two-story homes, brick or stone exterior walls, and homes with heavy mass above the footing.
A helical pier is a steel shaft with one or more steel screw plates welded to it. A torque motor on a hydraulic excavator screws the pier into the ground. The torque required to keep advancing the pier is read by a calibrated indicator, and that torque correlates directly to load capacity. When the pier reaches the target torque, capacity is verified.
Helical piers do not need building weight to be installed because they pull themselves into the ground. That makes them the right choice for porches, additions, light commercial buildings, deck footings, and new construction where the load above is too light to drive a push pier. They are also faster to install than push piers in many situations because they do not require waiting for each section to settle under the structure's weight.
| Property | Push Pier | Helical Pier |
|---|---|---|
| How driven | Hydraulic ram, weight resistance | Hydraulic torque motor |
| Capacity verified by | Final pressure at refusal | Installation torque |
| Best load type | Heavy structures | Light to medium structures |
| Typical depth in Wichita | 15 to 30 ft | 10 to 25 ft |
| Best for | Two-story brick homes, full basement walls | Porches, additions, new builds, light commercial |
| Lift capability | Excellent | Good |
For a deeper read, see steel piers vs concrete piers.
In 2026, push pier installations in Wichita generally run $1,500 to $2,500 per pier, all-in. A typical foundation repair project uses 6 to 12 piers, so most jobs land between $9,000 and $25,000. Helical piers run a similar range, with the actual number depending on capacity and shaft length. Read the full 2026 Wichita cost guide for a detailed breakdown.
Steel piers often pair with basement wall stabilization or slab foundation repair. After lift, hairline cracks are often sealed with crack injection. We serve Derby, Andover, and the rest of the Wichita metro.
See typical 2026 prices on the Wichita foundation repair pricing page. For local detail, read about foundation and basement problems across Wichita neighborhoods and newer slab homes in Maize.